Conventional FDAS
Initiating devices are grouped by zones, allowing the panel to show the affected area. A practical arrangement for selected smaller or straightforward properties.
Need a fire detection and alarm system? Start with a free site assessment.
We assess the property, define the detection and notification requirements, then handle design, supply, installation, testing, commissioning and follow-up.
- Site-based designDetection begins with the actual property
- Complete device scopePanel, detectors, alarms and interfaces
- Testing + documentationCommissioning through maintenance
Fire detection and alarm system types
The right detection arrangement depends on the property, occupancy, hazard, ceiling conditions, airflow, alarm sequence, required interfaces and approved plans. We review those details before recommending a system.
Addressable FDAS
Compatible devices and modules carry programmed addresses, allowing the panel to report more specific point, location and event information.
Aspirating smoke detection
A detector actively draws air through a sampling-pipe network. It can support early warning and selected difficult-access or critical applications.
Beam smoke detection
A projected beam monitors smoke obscuration across a large open area. It is considered where point-detector placement or access is difficult.
From
assessment
to
handover.
We review the property, required alarm sequence and existing interfaces before defining the FDAS scope and project sequence.
01
Site assessment
We review the property, current conditions, available plans and project requirements.
02
Design & planning
We define the panel, device layout, alarm sequence, interfaces and installation scope.
03
Review quotation
We discuss the proposed scope, inclusions, commercial terms and questions before approval.
04
Supply & installation
Equipment, cabling, devices and site work follow the agreed project scope.
05
Testing & commissioning
The installed system is tested and commissioned against the approved scope and sequence.
06
Service + BFP follow-up
We remain available for maintenance, project records and BFP-related follow-up within our scope.
FDAS already installed?
Keep every signal ready.
We provide preventive maintenance for existing fire detection and alarm systems based on the installed equipment, site conditions and agreed service scope.
- 01
Review the control panel, power supplies, batteries and visible system conditions.
- 02
Test the agreed detectors, manual stations, notification appliances and system interfaces.
- 03
Record faults, disabled points, device concerns and corrective work that may be needed.
- 04
Provide service records and BFP-related follow-up connected to our scope.
FDAS questions,
made clear.
Straight answers about system types, site assessment, project scope, existing systems, testing and BFP-related support.
A fire detection and alarm system monitors initiating devices such as smoke detectors, heat detectors and manual stations, processes their signals at the control panel, and activates the required alarm or control outputs for the approved design.
A conventional system groups initiating devices by zone, so the panel identifies the affected zone. An addressable system assigns identities to compatible devices or modules, allowing the panel to report more specific point and location information.
That depends on the building layout, occupancy, hazard, ceiling conditions, required alarm sequence, interfaces, expansion needs and approved plans. We review the site before recommending conventional, addressable or a special smoke-detection arrangement.
Send the contact person, company, site location, whether this is a new installation or an existing system, and any available floor plans, specifications, bill of quantities, device schedule or BFP comments.
Yes. We can define a coordinated scope covering assessment, design and planning, equipment supply, installation, programming where applicable, testing, commissioning and project documentation.
Yes. We can assess the installed panel and devices, agree on a practical inspection and testing scope, document findings, discuss corrective work and assist with BFP-related follow-up connected to our work.
Completed work
Related DGRB projects
Selected DGRB projects involving this equipment or system category.
Dairy-production office building
Conventional FDAS scope with a 10-zone panel, 27 smoke detectors, manual stations, strobe horns, conduit, wiring, testing, drawings and sprinkler monitoring.
Scope: Conventional fire detection and alarm system
View the projectTell us about your
FDAS project.
Send the site location, whether this is a new installation or an existing system, and any available plans or specifications. We’ll review the details and contact you about the site assessment and next steps.